senzor za vrata/okna stiku s suhimi in analogni senzor Fibaro

49,99

Brez DDV: € 41,31

Razpoložljivost:
Na zalogi
Šifra:
ES-11-FIB-FGK-10
Proizvajalec:
Fibaro

Možnosti

Opis artikla

Brezžični magnetni senzor za vsaka vrata ali okno.

TEHNIČNI PODATKI:

  • Življenska doba baterije: 2 leti (CR2 baterija)
  • Tamper stikalo (v primeru vandalizma)
  • Podpora Z-Wave protokola in standardov
  • Dimenzije: 20 x 34 x 79mm

The Fibaro Door / Window Sensor is a battery powered, Z-Wave compatible reed sensor. It combines the functionality of 3 devices (reed, binary and temperature sensor) in one easy to use product. The sensor can be used for monitoring whether a door, window, window blind or a garage gate is opened or closed. In addition, you can integrate any binary output sensor with the Z-Wave network using this sensor, e.g. motion sensors, flood sensors, alarm system sensors, etc.

In addition, the sensor has an analog input allowing to connect a temperature sensor DS18B20 1-Wire.

The product consists of two elements. One of the parts is mounted on the moving part of the window or of the door. The other part is placed on the frame. The device needs to be included into a Z-Wave network by a remote control or any other Z-Wave controller. If an action is detected, the sensor sends a signal to the Z-Wave network main controller.

FEATURES:

  • Opening detector
  • Button to include / exclude the detector
  • Low battery detection
  • Tamper protection
  • 1 potential free wired input
  • 1 analog input 1-Wire (for connecting a temperature sensor DS18B20)
  • Very small, small size
  • Ease of use and installation

SPECIFICATIONS:

  • Module Type: Z-Wave Transmitter
  • Colours: White, Grey, Black, Gray Claire, Claire Brown, Brown, Dark Brown
  • Power: Battery ER14250 (1/2AA) 3.6 V
  • Frequency: 868.42 Mhz
  • Transmission distance: 50m free field, 30 m indoors
  • Dimensions: 76 x 17 x 19 mm
  • Operating temperature: 0-40 ° C

 

Product Manual

Karakteristike

Glavni krmilnik Združljivost
eeDomus+ Full Compatible
Fibaro Home Center 2 v4.130 Full Compatible
Fibaro Home Center Lite v.4.080 Full Compatible
Vera Edge / Plus Full Compatible
Zipabox/Zipamini/ZipaTile Full Compatible
Piper / Piper NV (v.1.7.1) Full Compatible
Indigo Compatible (Testing)
jeedom full compatible
Domoticz Full Compatible
ZiHome Full Compatible
Vera 3 Full Compatible
Vera Lite Full Compatible
Tech Data
Power Supply Batery ER14250 3.6V
SDK 4.55
App Version 2.5
Device Type Routing Binary Sensor
Z-Wave Alliance Product Link http://products.z-wavealliance.org/products/1050
Procedures
Inclusion 1) Open the cover. 2) Remove the battery blocker. 3) Close the cover. 4) Locate the sensor nearby the main Z-Wave controller. 5) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 6) Quickly, triple click the TMP button located on the bottom of the casing. 7) Wait for the device to be added to the system. Successful adding will be confirmed by the controller. 9) Install the device using the attached self-adhesive pads.
Exclusion 1) Place the device within direct range of the Z-Wave controller. 2) Make sure that Sensor's cover is closed. 3) Set the main Z-Wave controller into learning mode (see main controller’s operating manual). 4) Quickly, triple click the TMP button. 5) Wait for the device to be excluded from the system. Successful exclusion will be confirmed by the controller.
Factory Reset Resetting the device is not the recommended way of removing the device from the Z-Wave network. Use reset procedure only if the primary controller is missing or inoperable. 1) Take off the Sensor's cover and remove battery. 2) Install the battery while holding both TMP buttons (after mounting the device, one button is constantly pressed by the cover). 3) Release the TMP button within 5 seconds. 4) LED will blink 3 times to confirm launching of reset procedure. 5) Reset procedure may last up to 30 seconds. Do not remove the battery until reset is complete. 6) Reset will be confirmed by the six blinks of the LED.
Wake Up FIBARO Door/Window Sensor will wake up at a defined time interval and will ALWAYS try to communicate with the main controller. Setting wake up interval to 0 disables sending Wake Up Notification frame automatically. There is a possibility to wake up the device manually by a single TMP button click.

Ocene - mnenja (7)

Napišite mnenje

Opomba: Uporaba HTML kode ni dovoljena!

Slabo            Dobro


Nadaljuj

Z-Wave Slovenija

Spletna trgovina za dom, trženje proizvodov za avtomatizacijo Z-Wave radio. Z-Wave je mednarodni standard za brezžično povezovanje sistemov notranjih kontrol. Lahko upravljate razsvetljavo, elektriko, rolete, alarmi, itd ... Z-Wave izdelki različnih ponudnikov delujejo dobro skupaj omogoča nadzor pametne hiše.

Contact Us

Phone:
+38613205694
GSM:
+38640208964
Phone:
+38613205695
E-mail:
info@zwave.si
Skype:
iztok.mahoric

Twitter

Facebook