€ 54,99
Brez DDV: € 45,45
Opis artikla
The Philio Sensor is a 2-in-1 Sensor. The sensor measures the humidity (in percent) and the temperature (in Celsius) of its environment. Furthermore the sensor has a tamperswitch, which works as a burglar alarm. By using Z-Wave all the information is transfered to the Gateway.
The 2-in-1 Sensor can be mounted on almost every surface in horizontal or vertical position. The sensor has a casing with a barred aperture for the measurement of the humidity. On the backside of the case there is the tamperswitch, which works as burglar alarm if the device is moved or manipulated.
Properties:
- Z-Wave Plus
- EU frequency: 868,42 MHz
- Package content: 1x 2-in-1 Sensor incl. battery
- Power supply: battery CR123A 3V
- Battery lifetime: 7 years (depending on the wake-up interval)
With the Philio sensors you can easily make your home smarter and safer. The sensors are small, inconspicuously and fit on every surface. If you want to protect your home from burglars or other dangers like fire or water you can easily integrate the Philio Sensors to your Z-Wave Smart Home gateway.
Karakteristike
| Glavni krmilnik Združljivost | |
|---|---|
| eeDomus+ | not tested |
| Fibaro Home Center 2 v4.160 | partly compatible/only usable in unsecure mode |
| Fibaro Home Center Lite v.4.160 | partly compatible/only usable in unsecure mode |
| Vera Edge / Plus / Secure | fully compatible |
| Zipabox/Zipaminicro/ZipaTile | not compatible |
| Piper / Piper NV (v.1.7.1) | not tested |
| Indigo | not tested |
| jeedom | not tested |
| Z-Wave.me / Z-Way / PoPP Hub v 3.2.1 | fully compatible |
| Domoticz | not tested |
| OpenHAB | not tested |
| ZiHome | not tested |
| Somfy Tahoma | not tested |
| Home Assistant | not tested |
| Telldus | not tested |
| Tech Data | |
| IP Rating | IP20 |
| FLiRS | battery CR123A 3V |
| Power Supply | battery CR123A 3V |
| Explorer Frames - NWI Support | Yes |
| SDK | 6.51.06 |
| App Version | SD3502 |
| Device Type | Multilevel Sensor |
| Z-Wave Alliance Product Link | https://products.z-wavealliance.org/products/1350 |
| S2 Security Frame | No |
| Procedures | |
| Inclusion | 1. Have Z-Wave™ Controller entered inclusion mode. 2. Pressing the tamper key three times within 1.5 seconds to enter the inclusion mode. 3. After add successful, the device will wake to receive the setting command from Z-Wave™ Controller about 20 seconds. |
| Exclusion | 1. Have Z-Wave™ Controller entered exclusion mode. 2. Pressing tamper key three times within 1.5 seconds to enter the exclusion mode. Node ID has been excluded. |
| Factory Reset | Notice: Use this procedure only in the event that the primary controller is lost or otherwise inoperable. 1. Pressing tamper key four times within 1.5 seconds and do not release the tamper key in the 4 th pressed, and the LED will light ON. 2. After 3 seconds the LED will turn OFF, after that within 2 seconds, release the tamper key. If successful, the LED will light ON one second. Otherwise, the LED will flash once. 3. IDs are excluded and all settings will reset to factory default. |
| Wake Up | When the device power on, the device will wake about 20 seconds. In this duration, the controller can communicate with the device. Normally the device is always sleeping to save the battery energy. |
